High mileage stelvio clutch job , clutch slipping because it is,a worn out ,b because the cush springs were rubbing on the gearbox casing .
Norge 8v GT ,
had a leaking oil pressure switch , to get to it involves seat, panels,and fuel tank …then you remove the lower fairing , on both sides to access the inlet manifolds to the throttle bodies .
then you can remove the airbox , underneath is the oil pressure switch. It also means you can get to everywhere to clean up the oil that has leaked out .
new switch has an adapter to fit new type of switch , so hopefully it won’t happen again .
clean everything up and screw it all back together.
customer went for MOT …MOT failed .
customer complained of poor back brake performance.
customer complained about MOT tester .
customer complained about cost of replacement pads.
mechanic , how long has your rear brake been poor ?
customer , for about the last 4 months .
mechanic , do you not check your bike over every now and again ?
customer , well the last mechanic said they were ok !
mechanic , when was that then ?
customer , last year just before the MOT.
mechanic , how many miles have you done since then ?
customer , 12,000 miles all in London.
mechanic , OH !
When there used to be lots of guzzi workshops in London , ….this is how we would send messages to each other .
I once took out a filter that was 25 years old , message written by a mechanic in 3 Cross . He still worked at a dealer nearby , took it to show him ….he nearly fell over !
ALWAYS have a minimum of 2 keys for your Breva , Griso , Stelvio , Cali 14 ,Norge , 1200 Sport, anything that has a key coded to the bike .
This customer managed to lose a set of keys ages ago, never got around to getting some more cut, even though he had brought some spares, to do just that .
Lost his only remaining set , didn’t have the key number written down , BUT does, thankfully , know his user code .
SO , new set of locks all-round , code the new keys to the dash , and off he goes,
£450 quid lighter .
ALL FOR THE SAKE OF NOT KEEPING A KEY SAFELY SOMEWHERE .
Special offer , all of June , if you don’t know your user code , but you have 2 keys , come and see me, and i will give you one , THAT YOU CANNOT FORGET OR LOSE .
THIS IS AS IMPORTANT AS HAVING 2 KEYS .
1200 Sport , one of my all-time favourite Guzzi’s , i don’t think there are 200 in the UK .
A do everything bike , comparable to a VFR750 , doesn’t do anything fantastic , just does everything well.
Fast enough to get from A 2 B at a very good average speed , comfy if you mod the seat a bit and put on the later bars , fuel efficient , 40+ mpg , good looking , forgiving chassis , good brakes , what more do you need?
Put on the factory 2 into 2 exhaust system , and lose a bit …ok a lot , of weight ,AND get some noise out of it .
So , a new owner says… give it a service , so we have a start point. Shouldn’t need much he says , i’ve only done 5-600 miles since i got it . Dropped the oil out and took off the sump… oil filter dated 2012 , thick black sludge in the sump , a drain washer that has been used more than once is cut off of the drain bolt. Double gaskets on the rocker covers ? and valves so very tight , carb balance a mile off , and mixture screws set at 2 turns out not the 3 1/2 turns out the engine wants .
Run it down the road for an MOT , tester can’t get it out of gear , passes with flying colours .
so what bike magazines /papers do you read ?
This is an alarm removed in 15 mins from a V7 . Fitted by a Datatool Dealer . Bike came to a halt , because it was so badly fitted . i don’t know any alarm fitter who would have done it like this , it was embarrassingly bad . Have spoken to Datatool who want it back , so they can see what has been done to it .
there is a wire to sense that the ignition has been switched on ….the wire was poked into the ignition live …it is supposed to be soldered in .
Hopefully a new unit is on it’s way , and a letter will be sent to the fitting dealer .
Norge 8V GT
broken exhaust collector box , needed welding .
here is what happens… next put bike on the bench , remove fairing panels, remove header pipes …deal with exhaust studs, deal with exhaust clamps to coll. box ,remove silencer, strap bike to bench , jack the bike up, chock rear wheel ( for a bit of height ) remove centre stand, 4 hours later collector box in your hand ! ….take to welders.